英國TTi CPX400D/CPX400DP可編程直流穩壓電源 

    概述: 產品特點: · 高性能的單組或雙組輸出 · PowerFlex設計了可變電壓和電流 · 在最大功率包絡的組合 · 每組輸出高達60V和20A,(420W最大) · 恒定電壓或恒定電流操作 · 輸出噪聲低和良好的瞬態響應 · PowerFlex或固定的操作范圍加上自定義的限制 · 真實的模擬控制與數字設置鎖定(S -鎖) · 獨立的輸出或隔離電壓跟蹤(D型) · 輸出可以串聯或并聯120V或40A · 獨立的或同步開關輸出(D型) · 可變OVP旅行安全接線端子; · 4位分辨率固定米;可選遙感

    刷新時間:
    2025-03-26 15:00:05 點擊100717次
    聯系電話:
    0139-22871080 楊聰
    QQ:
    396089365
    信用:4.0  隱性收費:4.0
    描述:4.0  產品質量:4.0
    物流:4.0  服務態度:4.0
    默認4分 我要打分

    英國TTi CPX400D/CPX400DP可編程直流穩壓電源

    CPX400D/CPX400DP是各地暢銷的線性穩壓電源,它集成了除數字接口的重要的新的手動控制功能。

    調節使PowerFlex 840瓦的總功率可以構造成適合每一個具體的應用。

    產品特點:

    ·        高性能的單組或雙組輸出

    ·        PowerFlex設計了可變電壓和電流

    ·        在最大功率包絡的組合

    ·        每組輸出高達60V和20A,(420W最大)

    ·        恒定電壓或恒定電流操作

    ·        輸出噪聲低和良好的瞬態響應

    ·        PowerFlex或固定的操作范圍加上自定義的限制

    ·        真實的模擬控制與數字設置鎖定(S -鎖)

    ·        獨立的輸出或隔離電壓跟蹤(D型)

    ·        輸出可以串聯或并聯120V或40A

    ·        獨立的或同步開關輸出(D型)

    ·        可變OVP旅行安全接線端子;

    ·        4位分辨率固定米;可選遙感

    ·        GPIB接口,串口,USB和LAN接口(cpx400dp和SP),

    ·        局域網接口C級LXI兼容

    ·        隔離的模擬遠程控制接口(cpx400sa只)

    ·        緊湊的1 / 4或1 / 2架3U尺寸

    ·        復制后的終端(cpx400dp,cpx400sp和cpx400sa)

    技術規格:

    OUTPUT SPECIFICATIONS (each output)

    Voltage/Current/Power Levels

    VoltageRange: 0V to 60V.
    CurrentRange: 0A to 20A.
    Note: Actual maxima for voltage and current are typically 1% greater than the figures given above.
    PowerRange: Up to 420W per output subject to power envelope.

    Power Envelope

    The maximum current at any voltage settings is limited by the power envelope which is set to give 7A at 60V rising to 20A at 20V under all ac supply conditions (both outputs loaded). At lower output voltages the power is restricted by the 20 amps current maximum.  See PowerFlex power envelope graph

    Output Setting & Control

    Voltage Setting: By coarse and fine controls.
    Current Setting: By single logarithmic control.
    Output Mode: Constant voltage or constant current with automatic cross-over. CC indicator for constant current mode.
    Output Switch: Electronic, non isolating. Preset voltage and current limit displayed when Output is off. 
                           Output rise time no load <10ms.
    View Settings: With the output On, the meters show actual voltage and current. The preset levels can be viewed and
                          adjusted at any time by pressing the View Settings button.
    Status Indication: LED indication of Output On, V/I Limits, CV, CI, Power Limit, Remote, LAN status. 
                              Message on meter display for trip condition.

    S-Lock (Settings Lock)

    Voltage and current settings can be locked by a single button press. Lock accuracy is equal to the meter accuracy (see Meter Specifications).

    Output Performance

    Ripple & Noise: Typically <3mV rms, <15mV pk-pk, in CV mode.
    Load Regulation: Voltage - <0.01% of maximum output for any load change within the PowerFlex envelope. 
                             Current - <0.05% of maximum output for any load change within the PowerFlex envelope.
    Line Regulation: Voltage - <0.01% of maximum output for a 10% line change.
                            Current - <0.01% of maximum output for a 10% line change.
    Transient Response: <250us to within 50mV of setting for a 5% to 95% load change.
    Temp. Coefficient: Typically <100ppm/oC

    Output Protection

    Output Protection: Forward protection by Over-voltage Protection (OVP) trip. 
                                Reverse protection by diode clamp for currents to 3A.
    OVP Setting/Range: Via screwdriver adjustable preset on front panel. Range 1V to 66V
    Over-temperature: Output trips off for over-temperature.
    Safety Interlocks: Operations that could cause an unexpected change in voltage or current settings are interlocked
                               with the output switch.

    Output Connections

    Power Terminals: Universal 4mm safety binding posts on 19mm (0.75") spacing at front. 
                               Screw terminals at rear (CPX400SP, SA and DP only).
    Remote Sense
    Sense Selection: Voltage sensing is selected as Local or Remote by front panel switch.
    Sense Terminals: Sprung loaded screw-less terminals at front. Screw terminals at rear (CPX400DP only).

    METER SPECIFICATIONS (each output)

    Display Type: Dual 4-digit meters, 10mm (0.39") LED.
    Voltage Meter
    Resolution/ Accuracy: 10mV; +/- 0.1% of reading +/- 2 digits
    Current Meter
    Resolution/ Accuracy: 10mA ; +/- 0.3% of reading +/- 20mA

    VOLTAGE TRACKING (Dual output models)

    Independent Mode
    In the normal mode of operation, each output is fully independent and isolated. Operation is equivalent to two single output power supplies.
    Voltage Tracking Mode
    The two outputs remain isolated, but the Slave voltage controls are disabled and the Slave voltage is set equal to the Master voltage. This can be used to generate tracking bipolar voltages, or tracking unipolar voltages relative to different grounds. 
    When voltages greater than 60V are required, the outputs can be wired in series to generate 0 to 120V with the voltage controlled from the Master.
    When currents greater than 20A are required, the outputs can be wired in parallel to create the equivalent of a 40A power supply with the voltage controlled from the Master.
    Track Accuracy: Slave voltage = +/- (0.1% of Master voltage setting + 10mV)

    BOTH ON / BOTH OFF (Dual output models)

    Each output has an independent DC On/Off control, however, an additional control button is provided which turn both outputs on or off simultaneously.

    DIGITAL BUS INTERFACES (CPX400SP and CPX400DP only)

    These models offers full remote control and read-back using RS-232, USB, GPIB or LAN (compliant with LXI class C).All interfaces are at ground potential and opto-isolated from the output terminals. Note: Remote/Local Sense, is manually selectable only.
    RS-232
    Standard 9-pin D connector. Baud rate 9,600.
    USB
    USB 2.0 connection (backwards compatible with USB 1.x). Operates as a virtual COM port.
    GPIB (IEEE-488)
    The interface conforms with IEEE-488.1 and IEEE-488.2.
    Ethernet (LAN)
    Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to Local Area Network or direct connection to a single PC.
    LXI Compliance
    LAN interface is compliant with LXI class C. (LXI is the abbreviation for Lan eXtensions for Instrumentation). For more information visit:www.tti-test.com/go/lxi

    DIGITAL PROGRAMMING PERFORMANCE

    Voltage Setting
    Resolution/Accuracy: 1mV; +/- (0.05% +10mV)
    Current Setting
    Resolution/Accuracy: 1mA; +/- (0.3% +5mA)
    Programming Speed
    Command Delay: Typically <25ms (this must be added to any of the figures below)
    Voltage Up Time: <10ms* to 1%
    Voltage Down Time: <80ms* to 1% (full load); <1.5s* to 1% (no load)
    * The up and down times vary with range and voltage step size. More information is contained in the operating manual which can be downloaded from our web site.

    DRIVER SOFTWARE SUPPLIED

    IVI Driver
    An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc.
    USB Driver
    An installation file is supplied which calls a standard Windows* USB driver.

    * LabView and LabWindows are trademarks of National Instruments. 
    HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. 
    * USB interface is supported for Windows 2000, XP,Vistaand Windows 7.
    Windows is a trademark of Microsoft.

    ANALOGUE REMOTE INTERFACE (CPX400SA only)

    The CPX400SA offers galvanically isolated analogue remote control of voltage and current from control voltages. Voltage and current front panel settings generate non-isolated analogue output voltages that can be used to control slave power supplies.
    Input Scaling: 0 to 100% control of voltage or current from 0 to 5V or 0 to 10V (selectable)
    Input Accuracy: Voltage: 0.3% +/-20mV. Current: 0.5% +/-50mA. Input impedance 10kOhms
    Output Scaling: Set values of 0 to 100% of rated output voltage and current generate 0 to 5V (not isolated)
    Output Accuracy: Voltage: 0.3% +/-20mV. Current: 0.5% +/-50mA. Output impedance 125Ohms
    Remote On/Off: Output On/Off can be controlled by external switch closure (not isolated)

    GENERAL SPECIFICATIONS

    Input
    AC Input: 110 to 240 volts +/-10% 50/60Hz. Installation Category II.
    Input Power: 1250VA max.
    Temperature & Environmental
    OperatingRange: +5oC to +40oC, 20% to 80% RH
    Storage Range: -40oC to + 70oC
    Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
    Cooling: Rear discharge variable speed fan. 
    Safety & EMC
    Safety: Complies with EN61010-1
    EMC: Complies with EN61326
    Physical
    Size: Single - 107 x 130 (1/4 rack 3U) x 398mm; Dual - 210 x 130 mm (1/2 rack 3U) x 377mm
    (size excludes feet, knobs and terminals).
    Weight: Single - 4.25kg (9.35lb), Dual - 6.3kg (13.9lb))

    OPTIONS

    Rack Mount (RM300A)
    19 inch 3U rack mount suitable for one or two dual power supplies.
    Rack Mount (RM460)
    19 inch 4U rack mount with above/below ventilation suitable for up to 4 single or 2 dual power supplies (or mixture)


    Accuracy specifications apply for the temperature range 18oC to 28oC after one hour warm-up.
    Thurlby Thandar Instruments Ltd. operate s a policy of continuous development and reserves the right to alter specifications without prior notice.

    [本信息來自于今日推薦網]
    • 13922871080發布的信息
    • PF8000 電功率分析儀
    • 聯系人: 楊聰,13922871080...
    • PW8001 PW6001功率分析儀
    • PW8001  PW6001功率分析儀 基本精度±0.03%,DC精度±0.05%,50 kHz精度±0.2%*1 準確捕捉高速開關產生的功率變化 采樣率18bit,抗干擾性(CMRR)110dB/10...
    • 颯特SATIR D300 D600全自動工具型熱像儀
    • 產品優勢:高靈敏640×480探測器 高速圖像處理引擎 獨創DUO-VISION PLUS技術 ★ D600具有兩種調焦方式,確保獲得對焦清晰的圖像 為滿足用戶對于調焦的不同需求,D600具有自動, 電動兩種調焦方式,用戶可根據需要自由切換,確保每 一次都能獲得完美對焦的圖像。 ★ 采用先進的USB Type C接口,提升的何止一點點 新一代的USB Type C接口,完美實現正反插充電無 壓力;更快的文件傳輸,更長久的使用壽命。 ★ 高清高質量熱圖 D600采用最新的圖像處理技術來減少干 擾,再加上640x480紅外探測器的出色性能, D600可生成高質量的紅外圖像,并具有清晰 明確的細節....
    • 颯特HM300紅外熱像儀
    • 項目 內容 技術指標 探測器 探測器類型 焦平面(FPA), 非制冷微量熱型(microbolometer) 工作波段 7.5-14 μm 像素數 384×288像素 發射率設定方式 0.1至1 輻射率可以0.01為步進校正 距離系數 可調;內部自動校正 成像參數 視場角 標準鏡頭:24°x 18°/0.1m 調焦方式 手動調焦...
    • NoiseKen ESS-B3011A ESS-S3011A靜電放電發生器
    • NoiseKen的ESS-B3011靜電放電發生器為最新型號!ESS-B3011是2011年一款全新的設計使產品。ESS-2002EX已停產代替使作型號為:ESS-B3011.ESS-B3011為30kV輸出,2011年年底開始出售;更簡單、使用操作更方便;...
    • 組合波雷擊浪涌模擬器CWS 600G/800G
    •  5.7寸彩色觸摸屏前面板操作 . > 浪涌失效偵測功能 > 浪涌電壓 6kV/8kV 浪涌電流 3kA/4kA > 測試排程功能 操作簡單 > 浪涌電壓、電流監測 LCD顯示 > 可控制外置三相耦合/去耦網絡 > 外置磁場線圈,滿足IEC61000-4-9測試...
    主站蜘蛛池模板: 国产1000部成人免费视频| 国产成人免费观看| 四虎www成人影院| 成人性生交大片免费视频| 成人欧美视频在线观看| 成人看片黄a在线观看| 成人a毛片在线看免费全部播放| 成人免费视频一区二区| 国产综合成人亚洲区| 亚洲国产成人精品女人久久久| 亚洲国产成人精品女人久久久 | 成人观看网站a| 国产成人精品免费视频大全麻豆| 国产成人精品亚洲精品| 四虎www成人影院| 无码国产成人av在线播放| 国产成人mv在线播放| 成人国产网站v片免费观看| 亚洲最大成人网色| 成人免费无毒在线观看网站| 亚洲国产成人久久一区www| 成人亚洲欧美日韩在线| 四虎www成人影院免费观看| 成人嗯啊视频在线观看| 78成人精品电影在线播放日韩精品电影一区亚洲 | 成人AAA片一区国产精品| www.成人av.com| 亚洲国产精品无码成人片久久| 天天欲色成人综合网站| 成人妇女免费播放久久久| 欧美成人在线免费观看| 亚洲人成人77777网站| 成人妇女免费播放久久久| 欧美日韩国产成人高清视频| 2022国产成人精品福利网站| 四虎成人精品免费影院| 亚洲美女人黄网成人女| 亚洲国产成人va在线观看| 免费网站看v片在线成人国产系列| 国产成人精品免费视频大全办公室| 女性成人毛片a级|